MENÜ

Crown

DCI 4/2400N

8 Ohm Amfiler
Marka:
Ürün Kodu:
Kategori:
Barkod:

  • TEKNİK ÖZELLİKLER
  • DETAYLAR
  • DÖKÜMANLAR
ÖZELLİKLER
TEKNİK ÖZELLİKLER
Frequency Response ( 8 Ohms, 20 Hz - 20 kHz) +/- 0.25 dB
BLU Link Input Signal to Noise Ratio (A-Weighted) > 108dB
Total Harmonic Distortion (at full rated power, 20 Hz - 20 kHz) 0.35%
Voltage Gain 34 dB
Damping Factor (20 Hz to 100 Hz) >5000
Input Impedance (nominal balanced, unbalanced) 10 kOhms, 5 kOhms
Maximum Input Level before Compression +20 dBu
Load Impedance (Stereo/Dual Mode) 2 - 16 Ohms; 70Vrms and 100Vrms
Load Impedance Bridge Mono 4 - 16 Ohms; 140Vrms and 200Vrms
Cooling Continuously variable speed forced air, front to back airflow
Required AC Mains (+/- 10%) 100V-240V ~ 50/60 Hz
IEC Power Connector 30A IEC
Dimensions 19" x 3.5" x 19" (48.3cm x 8.9cm x 48.3cm)
Weight 29lbs (13.15kg)
DETAYLAR
DETAYLAR

The new DriveCore install series amplifiers is a complete line of high performance installation amplifiers based on the proprietary DriveCore technology. DCi Series amplifiers are designed, engineered and manufactured to the industry’s highest quality standards, and provide system integrators with the advanced features and flexibility required for challenging 21st century installed sound applications. Versatile, compact and highly energy-efficient, DCi Series amplifiers continue the unbroken Crown tradition of leadership in professional and commercial power amplifier technology. 

Get DCi Certified!

Network Power Matrix

Network Power Matrix Bridge

Video 1: DriveCore Install Analog vs Network Comparison

Compares and contrasts the different DriveCore Install (DCi) Network amplifier models

Video 2: Software/Processing Overview

A basic overview of the DSP features inside a DCi Network amplifier

Video 3: Input Routing - Analog

How to route analog audio with a DCi Network amplifier

Video 4: Input Routing - BLU link

How to route BLU link digital audio with a DCi Network amplifier

Video 5: How To Select High Z (70V/100V)

How to configure a DCi Network amplifier for high impedance speaker loads (70V/100V)

Video 6: Mode Settings: Input Y & Bridge

How to configure a DCi Network amplifier for Input Y and Bridge modes

Video 7: Priority Input Routing

How to configure a DCi Network amplifier for redundant input sources

Video 8: Signal Generator

How to use the built-in signal and noise generator in a DCi Network amplifier

Video 9: Aux Port - Sleep & Amp Status

Explains the Sleep and Amp Status features of the AUX Port of a DCi amplifier and shows how to configure these features

Video 10: Storing Settings Part 1 - Speaker Tunings

How to save, load, and distribute amplifier Speaker Tunings

Video 11: Storing Settings Part 2 - Presets

How to save, load, and distribute amplifier Presets

Video 12: Storing Settings Part 3 - Device Files

How to save, load, and distribute amplifier Device Files

Video 13: Using Contrio Controllers with DCi Amplifiers

How to configure the BSS Contrio Wall Controllers to work with a Crown DCi Network amplifier

Video 14: How To Update Firmware

How to update firmware in a DCi Network amplifier

Video 15: Amplifier Factory Reset

How to perform a Factory Reset on a DCi Network amplifier

Video 16: How To Set Amp Channels To Auto Standby

How to configure independent amp channels to enter a low-power Auto Standby state based on user-adjustable settings

Video 17: How To Route Audio onto the BLU link Bus

How to route audio from the analog inputs of a DCi Network amplifier onto the BLU link BUS for distribution to other devices in the BLU link ring

Video 18: How To Configure Continuous Load Monitoring

How to configure a DCi Network amplifier to monitor and report errors in output load impedance

Video 19: How To Monitor & Report Input AC Line Errors

How to monitor and report errors based on the Input AC Line powering a DCi Network amplifier

Video 20: How To Configure BLU link For 48/96kHz

How to switch between 48kHz (default) and 96kHz sampling rate for BLU link audio

Video 21: Crown DriveCore Install Network & BSS Audio BLU8v2

How to use BSS Audio BLU8v2 for VCA control of a Crown DriveCore Install Network amplifier

DÖKÜMANLAR
DÖKÜMANLAR
RESİMLER
RESİMLER
ETİKETLER
ETİKETLER

ÜRÜN AİLESİ